Dredges and Dredging Equipment
Dredge Brokers HomeList your Dredge or Equipment (Free)Dredge Brokers Terms of UseDredge Brokers Privacy PolicyFrequently Asked QuestionsHow To Contact Dredge Brokersfiller

File 110722-BW

Shakerton Sectional Barges (NEW)
More Photos

Shakerton Sectional Barges (NEW)

    Located in The State of Indiana, USA

    Price for Sectional Barges: USD $

  • ST:405 40' x 10' x 5' $37,200        ST: 718 Spud Well $5,350
  • ST:305 30' x 10' x 5' $30,550        ST: 16" Spuds $140.00 per foot
  • ST:205 20' x 10' x 5' $19,425        All STD Deck Fittings $ Price upon request
  • STR: Rakes are the same price
  • HD: Series barges are 7' deep         HD: 924  Spud Well $7,225
  • HD:407 40' x 10' x 7' $50,500          HD:1216 Pin On Ramp $13,350 
  • HD:307 30' x 10' x 7' $39,400          HD: 22" Spuds $ Price upon request
  • HD:207 20' x 10' x 7' $27,200
  • HDR: Rakes are the same price

Other sizes available along with Rake sections, Spud wells, Spuds, Ramps, and Hydraulic Jack -Up systems.

Technical Details
Principal Dimensions and Characteristics
  ST Series Barges:
  ST:405 dimensions (length x width x depth): 12.19 x 3.05 x 1.52 m 40 x 10 x 5 feet
  ST:305 dimensions (length x width x depth): 9.14 x 3.05 x 1.52 m 30 x 10 x 5 feet
  ST:205 dimensions (length x width x depth): 6.10 x 3.05 x 1.52 m 20 x 10 x 5 feet
  HD Series Barges:
  HD:407 dimensions (length x width x depth): 12.19 x 3.05 x 2.13 m 40 x 10 x 7 feet
  HD:307 dimensions (length x width x depth): 9.14 x 3.05 x 2.13 m 30 x 10 x 7 feet
  HD:207 dimensions (length x width x depth): 6.10 x 3.05 x 2.13 m 20 x 10 x 7 feet
   
  All steel plate is A-36 1/4" thick.
  All framing is made of A-36 3" x 3" x 1/4" angle frames spaced 17.25" apart.
  Connector angles are A-36 6" x 4" x 5/8" thick, welded solid to the outer hull.
  Connector holes are  spaced 24" apart on center.
  Connector pins are 1.5" dia. with a 6" double round cap.
  All seams are welded 100% solid inside and outside. Each unit is air tested 3-5 psi.
  All units are put into configurations and tested for alignment prior to blasting and coating.
  This process makes sure the barges are hassle free when it comes to joining the units together.
  All units are sand blasted to a near white on the outside and coated with a 2 part salt resistant epoxy by
  Devoe called Bar rust 235 in Haze gray.
  All units come standard with 1-18" flush mounted hatch for access without torching the deck just to get
  inside the barge.
  Each unit is sold with all connector pins needed.

All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice.

Go to Top
DredgeBrokers © 2007
Dredge Brokers Design by thewritersforhire.com