       |
File 100825-DH
 |
|
4 x 6 inch VMI MD-415 Auger Cutter Dredge
This Dredge was built in 1973 & reconditioned by prior owner and was purchased by the current owner on 02/25/2009. It does not have any discharge hose or pipe, but there is a hose that connects the pump to the back section of the dredge were it discharges. It can be hauled on a drop deck trailer no permit required.
Located in The State of Louisiana, USA
Price for Dredge: USD $ 55,000 |
Technical Details
| Principal Dimensions and Characteristics |
| |
Length Over All: |
9.94 m
|
32.6 feet |
| |
Height (with cab): |
2.44 m |
8 feet |
| |
Width (transport): |
2.59 m
|
8.6 feet |
| |
Width (working): |
2.74 m
|
9 feet |
| |
Draft: |
559 mm
|
22 inches |
| |
Weight: (approx.) |
9,100 kg
|
20,000 lbs |
| |
Fuel capacity: |
606 liters |
160 gallons |
| |
Year Built: |
1973 |
| Main Engine |
| |
Make/Model: |
Cummins / 6 BT5.9 |
| |
Power @ 2,500 RPM |
113 kW |
152 hp |
| |
Continuous: |
90 kW |
121 hp |
| Pump |
| |
Type: |
Hi-chrome cast iron, centrifugal, recessed impeller |
| |
Impeller: |
330.2 mm |
13 inches |
| |
Suction: |
101.6 mm |
4 inches |
| |
Discharge: |
101.6 mm |
4 inches |
| |
Capacity: |
Variable to 1,000 GPM @ 130 ft. (40 m) head (water @ 68 degrees F) @ 1,750 RPM |
| Cutter Assembly |
| |
Diameter: |
16 in. x 8.6 feet (406.4 mm x 2.59 m) with full width flow through suction. |
| |
Speed: |
Variable 0 - 120 RPM forward and reverse. |
| |
Torque: |
4,000 in. lbs., peak @ 7,000 in. lbs. |
| Working Capacity |
| |
Cut: |
2.59 m |
8.6 feet |
| |
Operating Depth: |
Variable 15 ft. (4.57 m) max. |
| Pontoons |
| |
Two (2) Pontoons: |
812.8 mm x 863.6 mm x 9.02 m |
32 in. x 34 in. x 29.6 ft. |
| |
12 gauge steel, integral bulkheads and stiffeners, formed for rigidity, cor0foam filled |
| Propulsion |
| |
Type: |
Treble sheave hydraulic winch |
| |
Traverse Speed Variable 0-50 FPM |
| |
Average Cutting Speed 5-15 FPM |
| Hydraulic System |
| |
Make/Model: |
Sundstrand |
| |
Pumps |
variable displacement, axial piston |
| |
Motors: |
fixed displacement |
| |
Capacity Total: |
Total 80 GPM (302.8 L/min) @ 2,200 RPM |
| |
Reservoir: |
170 liters |
45 gallons |
| Drive |
| |
Dual hydraulic pump drive direct from the engine |
| Filters |
| |
Protected hydrostatic loop, high pressure suction & return |
| Relief Settings |
| |
Centrifugal Pump: |
4,000 psi (276 bar)
|
| |
Cutter Head: |
3,000 psi (207 bar) |
| |
Accessories: |
3,000 psi (207 bar) |
| |
Boom: |
1,500 psi (103 bar)
|
| Electrical system |
| |
Alternator Output: |
42 amp |
| |
Battery Heavy Duty: |
12 volt Heavy duty |
| Gauges |
| |
Oil Pressure |
| |
Temperature |
| |
Volt Meter |
| |
Hydraulic Pressure |
| |
Oil Temperature |
| |
Hour Meter |
| |
Pump Pressure |
| |
All Circuit Hydraulic Pressures |
| Prime Finish |
| |
Lower Structure Coal Tar Epoxy Paint |
| |
Upper Structure Blue and White Epoxy Paint |
All details on these pages are given in good faith
and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose
is either stated or implied. Prices are subject to change without notice.
|
|
|
| DredgeBrokers © 2007 |
| Dredge Brokers Design by thewritersforhire.com |
Hydraulic Dredges