       |
File 110136-DH
 |
|
14 x 12 Shark Dredge
This 14 x 12 Shark Dredge is a model # DSC 750 Series.
Located in Mexico
Price for Dredge: USD $ 855,000 |
Technical Details
| Principal Dimensions and Characteristics |
| General |
| |
Length Over All (with ladder): |
25.48 m
|
83.6 feet |
| |
Length Over All (with side tanks): |
5.58 m
|
18.3 feet |
| |
Hull Depth: |
1.52 m
|
5 feet |
| |
Mean Draft (with fuel): |
10.36 m
|
34 feet |
| |
Ladder length (with cutter): |
13.11 m |
43 feet |
| |
Spud length (each): |
12.19 m |
40 feet |
| |
Spud weight (each): |
3.000 lbs. |
| |
Approx. Dredge weight: |
120,000 lbs. |
| Dredging Capacities (Operating Conditions) |
| |
Digging depth: |
| |
Minimum: |
1.52 m |
5 feet |
| |
Maximum: |
9.14 m |
30 feet |
| |
Maximum Cut of Dredge (Single Cut) |
| |
@ Minimum digging depth: |
21.34 m |
70 feet |
| |
@ Maximum digging depth: |
27.43 m |
90 feet |
| Dredge Specifications |
| Hull |
| |
Three (3) piece sectional hull: |
| |
Side sections (2): |
16.76 x 1.52 x 1.52 m |
55 x 5 x 5 feet |
| |
Center section (1): |
10.67 x 2.62 x 1.52 m |
35 x 8.6 x 5 feet |
| |
Over All dimensions: |
16.76 x 5.58 x 1.52 m |
55 x 18.3 x 5 feet |
| Main Engine |
| |
Make/Model: |
Caterpillar / 3412 DITA |
| |
Power @ 2,100 RPM |
559 kW |
750 hp |
| Cutter Module |
| |
Make/Model: |
DSC CD 3.75 |
| |
Cutting force: |
7,944 lbs. |
| |
Operating torque: |
135,054 lbs. |
| |
Cutting force per linear inch: |
234 lbs. |
| |
Cutter diameter: |
864 mm ID |
34 inches ID |
| |
Shaft diameter: |
95.25 mm |
3-3/4 inches |
| |
Cutter rating (power): |
45 kW |
60 hp |
| |
Cutter speed variable: |
28 RPM |
| Winches |
| |
Swing Winches: |
| |
Line pull: |
12,000 lbs. |
| |
Line speed: |
22.86 m/min. |
75 feet/min. |
| |
Drum capacity: |
97.54 m |
320 feet |
| |
Ladder Winches: |
| |
Line pull: |
8,000 lbs. |
| |
Line speed: |
35.36 m/min. |
116 feet/min. |
| |
Wire size: |
14.27 mm |
9/16 inch |
| |
Spud Winches: |
| |
Line pull: |
5,000 lbs. |
| |
Line speed: |
30.48 m/min. |
100 feet/min. |
| |
Wire size: |
14.27 mm |
9/16 inch |
| Dredge Pump |
| |
Suction: |
356 mm |
14 inches |
| |
Discharge: |
305 mm |
12 inches |
| |
Impeller diameter: |
914 mm |
36 inches |
| |
Material: |
Hi-chrome |
| Spuds |
| |
Type: |
Square |
| |
Size: |
4.88 x 4.88 m |
16 x 16 feet |
| |
Length: |
12.19 m |
40 feet |
| |
Wall thickness: |
7.92 mm |
5/16 inches |
| Service Water Pump |
| |
Make/Model: |
Peerless / F21020A |
| |
Size: |
2-1/2 x 2 - 10 |
| |
Impeller size: |
254 mm |
10 inches |
| Electrical system |
| |
Battery: |
24 VDC |
| Capacities |
| |
Fuel: |
6,814 liters |
1,800 gallons |
| |
Hydraulic: |
1,136 liters |
300 gallons |
| Additional Features |
| |
Operator's chair |
| |
Fire extinguishers (2) 10-Pound ABC |
| |
Lighted ring buoy |
| |
Handrails and kick rails |
| |
Guards |
| |
Early warning alarm and engine shutdown system |
| |
Digging depth gage |
| |
Cabin lights & cab heater |
| |
Bilge pump - electric |
| |
Replaceable point cutter |
| |
Dredge pump priming system |
| |
Dredge wash down system |
| |
Hi-capacity service pump |
| |
Paint: Hull - sand blast and coat with coal tar epoxy paint. |
| |
Paint: Superstructure and structural - sand blast and coat with primer and topcoat of paint. |
All details on these pages are given in good faith
and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose
is either stated or implied. Prices are subject to change without notice.
|
|
|
| DredgeBrokers © 2007 |
| Dredge Brokers Design by thewritersforhire.com |
Hydraulic Dredges