Dredges and Dredging Equipment
Dredge Brokers HomeList your Dredge or Equipment (Free)Dredge Brokers Terms of UseDredge Brokers Privacy PolicyFrequently Asked QuestionsHow To Contact Dredge Brokersfiller

File 81206-DH

10 inch Dixie Dredge
Dredge Photos
Condition Report

10 inch Dixie Dredge

This Dixie Dredge has been modified to accept either a ladder or submersible Toyo Pump. If using the Toyo Pump, it can reach over 95 feet deep.  All diesel engines, Toyo pump, main dredge pump and hydraulics completely overhauled in 2007.  Presently fully operational and ready for inspection.  A new (December 2008) condition and valuation survey available upon request.  Can be disassembled and easily transported on flat bed trucks.

The ladder is built in sections, and if all sections are assembled the ladder is 87-feet (26.5 m) long. The current owner uses the submersible pump dredging system, and has not used the ladder, however he has tested the cutterhead and proven that it works.

Built in: 1976

Located in the State of Texas, USA

Price for Dredge: USD $ 209,000

The Toyo Hydraulic Dredge Pump listed below can also be purchased separately, see file #81236-DC.
Technical Details
Principal Dimensions and Characteristics
  Date Built:   1976
  Length Over All: 19 m 62 feet
  Beam: 7 m 24 feet
  Depth: 1.2 m 4 feet
  One Center Hull:        

9 m x 2.4 m x 1.2 m

28 feet x 8 feet x 4 feet
  Four aft or rear pontoon tanks (cylindrical): each 10 m x 1.2 m 32 feet x 4 feet
  Two forward pontoon tanks (section barges): each 9 m x 3 m x 0.9 m

30 feet x 10 feet x 3 feet each
  Ladder is in three sections (not installed)  
  Rear Section: 14 m x 1.2 m x 0.9 m

47 feet long 4 feet x 3 feet
  Middle Section: 10 m x 1.2 m x 0.9 m 32 feet long 4 feet x 3 feet
  Front / cutter head section: 5 m x 1.2 m x 0.9 m

16 feet long 4 feet x 3 feet
  Ladder A- Frame: 5.4 m x 5.4 m x 4 m 18 feet high x 18 feet wide, 12 inch H beam construction
 

Two spud holes on stern of main center section

 
Main Engine (for dredge pump)
  Make/Model: Cummins Model / NTA855C360
  Overhauled (complete):

November 2006

  
 

Equipped with sea water pump to cool heat exchangers

  
Main Engine (for hydraulic power for Toyo Pump)
  Make/Model: Cummins Model / NTA855C360
  Overhauled:

November 2006

  
  Sea Water Pump: Model B3JRBM
  
  Hydraulic fluid pump:

Sauer Danfoss Model 9920558

  

Toyo Hydraulic Dredge Pump
  Make/Model:

Toyo / TO-150B
  Size:

254 mm

 10 inches
  Overhauled (complete):

May 2007

Auxiliary Engine (for hydraulic fluid)
  Make/Model:

Cummins / 07C4
  Overhauled:

November 2006
  Alternator: Installed 2,000 watts

Dredging Equipment
  One (1)

Toyo submersible centrifugal dredge pump Model DP-150B, capacity 3200 gallons per minute with water jet and suction connection, and hydraulic lines from control cabin.
  One (1)

10 inch Emco/Ronan mass flow meter for production rates.
  One (1)

3” centrifugal water pump, manufactured by Berkley, working pressure estimated at 150 PSI with maximum of 705 rpm, sustained and powered by a single 4-cylinder diesel engine located on forward pontoon.
  One (1)

80 ft x 10 inch diameter flex hose suction pipe for dredge pump with 45 degree elbow pump connection.
  One (1) Twinkle flow meter with analog gauge readout hookup located at control cabin.
Parts and Accessories
  One (1)

Toyo pump spare parts to include hydraulic pump motor, impeller, volute and upper casing
  Two (2) Deck hand winches for anchor cables
  Two (2)

Deck hydraulic winches for anchor cables
  One (1)

Complete set of hand and special tools for dredge maintenance      

  One (1)

Complete set of safely equipment including fire extinguishers, life rings and first aid kit.

All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice.

Go to Top
DredgeBrokers © 2007
Dredge Brokers Design by thewritersforhire.com