       |
File 91116-DH
 |
|
Nessie Dredge and Tandem Trailer
This Nessie Dredge model # N8DX was built in 2004 and has approximately 4,500 runtime hours. It is in good working condition and comes with a Hydraulic tilt - 2 axle - 8 wheel tandem trailer.
Approximately 2,000 feet of pipeline available at additional cost.
"PRIMIER AUGER": 5,000 lb Hydraulic Auger (used for drilling holes)
available at additional cost.
Located in The State of Florida (West Coast), USA
Price for Dredge & Trailer: USD $ 200,000 |
Technical Details
| Principal Dimensions and Characteristics |
| Dredge |
| |
Year Built: |
2004 |
| |
Length of hull: |
6.68 m
|
21.9 feet |
| |
Width of hull: |
2.23 m |
7.3 feet |
| |
Width with outriggers: |
4.54 m
|
14.9 feet |
| |
Dredge height: (Dry) |
2,261 mm
|
89 inches |
| |
Draft: (depth in water) |
432 mm
|
17 inches |
| |
Freeboard: |
660 mm
|
26 inches |
| |
Weight of dredge: (Dry) |
16,592 lbs |
| |
Outrigger pontoons: |
10 - Polyethylene |
| |
Arm swing pontoons: |
2 - Polyethylene |
| |
Spuds: (4) - (Square Tubes) |
127 mm x 127 mm x 7.32 m |
5 in. x 5 in. x 24 ft. |
| |
Spud weight: (each) |
500 lbs |
| |
Dredge arm, length: |
6.10 m |
20 feet |
| |
With cutterhead: |
7.62 m |
25 feet |
| |
Maximum horizontal sweep: |
15.85 m |
52 feet |
| |
Maximum depth reach: |
6.10 m |
20 feet |
| |
Bucketwheel cutterhead: (diameter x width) |
1,067 mm x 254 mm |
42 in. x 10 in. |
| |
Weight: |
580 lbs |
| |
Cutterhead drive: |
Auburn Gear |
| |
Planetary gear ratio: |
16.88 to 1 |
| |
Power: (at rated speed) |
31 kW |
42 hp |
| |
Torque: |
2,080 ft. lbs. |
| Main Engine |
| |
Make/Model: |
Caterpillar / 3126 Diesel Turbocharged - After cooled |
| |
Continuous Power @ 2,400 RPM |
164 kW |
220 hp |
| |
Intermittent Power @ 2,500 RPM |
186 kW |
250 hp |
| |
Electric starting: |
12 volt |
| |
Alternator: |
115 amp |
| |
Battery capacity: |
90 sec, Crank time |
| |
Fuel consumption: |
43.5 liters / 2,200 RPM |
11.5 gal / 2,200 RPM |
| |
Fuel capacity: |
413 liters |
109 gallons |
| |
Weight: (Net dry) |
1,210 lbs |
| Keene Dredging Pump |
| |
Weight: |
2,130 lbs |
| |
Material: |
White Iron High Chrome / 650 Brinell Minimum Hardness |
| |
Impeller design: (Vortex) |
203 mm x 203 mm x 635 mm |
8 in. x 8 in. x 25 in. |
| |
Maximum passing sphere: (diameter) |
200 mm |
7-7/8" |
| |
Maximum working pressure: |
(56 m) 185 feet of head (80 P.S.I.) |
| Priming Pump |
| |
Make/Model: |
Keene / 350 |
| |
Intake: |
102 mm |
4 inches |
| |
Discharge: |
76 mm |
3 inches |
| |
Capacity: |
400 GPM |
| Cooling Pump |
| |
Make/Model: |
Keene / 135 |
| |
Intake: |
51 mm |
2 inches |
| |
Discharge: |
32 mm |
1.25 inches |
| |
Capacity: |
125 GPM |
| Hydrostatic Power System (Open Loop) |
| |
Durst Dual Pump drive with 1.15 to 1 ratio speed increaser. |
| |
Pump: |
| |
Make/Model: |
Sundstrand / 90-100 - 6.1 cu. in./rev. - Variable Displacement Piston Pump |
| |
Motor: |
| |
Make/Model: |
Sundstrand / 90-100 - 6.1 cu. in./rev. - Fixed Displacement Piston Motor |
| Hydraulic Power System (Closed Loop) |
| |
Two (2) Sundstrand Pumps |
| |
Make/Model: |
Tap 22/90/33.5 |
| |
Displacement: |
2.02 cu.in./rev. (Fixed) |
| |
Rated speed: |
3,000 RPM |
| |
Rated Pressure: |
3,800 P.S.I. |
| Directional Controls |
| |
Twin Joysticks for all functions of Dredging Arm.... Electric switches for other functions. |
| |
Electo-Hydraulic solenoid 4-Way valves |
| Thruster - Hydraulic Propulsion |
| |
Two (2) Sundstrand Gear Motors |
| |
Make/Model: |
Tam-22/90-26.5 - 1.62 cu.in./rev |
| |
Rated pressure: |
3,800 P.S.I. |
| |
Power: (At maximum speed and pressure) |
30 kW |
40 hp |
| |
Propellers: |
Michigan Wheel |
| |
3 Blades, 14 in.(mm) diameter, 21 degree pitch - cupped |
| Trailer |
| |
Hydraulic Tilt - 2 Axle - 8 Wheel Tandem |
| |
Axle dimensions: (Face to Face) |
2,350 mm |
92.5 inches |
| |
Capacity: (each) |
10,000 lbs |
| |
Total capacity: |
20,000 lbs |
| |
Brakes on all axles: |
Electric |
| |
Tires: |
Eight (8) Steel belted radials LT235-85R16 |
| |
Rims: |
16" 8 lugs |
| |
Load rating: (each) |
3,250 lbs |
| |
Maximum combined load capacity: |
26,000 lbs |
| |
Ball size for coupler option: |
51 mm |
2-5/16 inches |
| |
Coupler loading rate: |
25,000 lbs |
| |
Lunette option - for Pintel hitch - rating: |
30,000 lbs |
| |
Fifth wheel - option - Gooseneck rating: |
25,000 lbs |
| |
Hydraulic tilt, Maximum inclination from level: |
9 degrees |
| |
Trailer tilt cylinder: |
4 in. (102 mm) bore x 30 in. ( 762 mm) stroke |
| |
Trailer gross weight: (approx.) |
4,260 lbs |
| |
Overall length: |
8.53 m |
28 feet |
| |
Overall Width: |
2.56 m |
8.4 feet |
All details on these pages are given in good faith
and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose
is either stated or implied. Prices are subject to change without notice.
|
|
|
| DredgeBrokers © 2007 |
| Dredge Brokers Design by thewritersforhire.com |
Hydraulic Dredges