       |
File 91121-DH
 |
|
IMS 5012 LP Auger Dredge
The Model 5012 LP Versi-Dredge was built in 2005, it is ideal for dredging in canals, lakes, and marinas where maneuverability is confined areas is an issue. Like all Versi-Dredge systems the Starwheel Drive system allows the dredge to be completely self-propelled. The 5012 LP can be converted into a weed harvesting machine by simply switching out the standard cutterhead with the Weedmaster Cutterhead. The LP (Low Pressure) pump on the 5012 LP is a fabricated steel pump with a rubber liner. It can be used in a variety of materials including abrasive sand. The unique LP pump design allows the 5012 LP to pass up to a 6” solid making it ideal for debris filled waterways. The LP pump is known around the globe for being extremely versatile, easy to maintain / rebuild in the field, and hard to break. The 5012 LP can be shipped on a 40’ flat rack making international freight very affordable.
Located in the State of Georgia, USA
Price for Dredger: USD $ 220,000
"Trailer is available for purchase at additional cost."
|
Technical Details
| Principal Dimensions and Characteristics |
| |
Length Over All: |
12.9 m
|
42.5 feet |
| |
Width: |
3.4 m |
11.3 feet |
| |
Height: (with pre-cleaner removed) |
3.1 m
|
10 feet |
| |
Weight: (less fuel): |
12,662 kg
|
27,915 lbs |
| |
Displacement: |
13,245 kg
|
29,200 lbs |
| |
Draft: |
762 mm |
30 inches |
| Flotation |
| |
Pontoons: |
| |
Two (2) pontoons: |
991 mm x 965 mm x 9,144 mm |
39 in x 38 in x 360 in |
| |
10 ga. steel sides, bottom and 1/4" diamond plate tops; internal bulkheads and stiffeners, and coated w/marine grade epoxy-urethane paint. |
| Working Capacity |
| |
Cut: |
2.743 mm (wide) x 559 mm (deep) |
108 in (wide) x 22 in (deep) |
| |
Working Depth: |
6.1 m |
22 feet |
| |
Extensions available to: |
8.5 m |
28 feet |
| Main Engine |
| |
Make/Model: |
John Deere Diesel / 6090HF070 / 6 cyl. 9.0 liter |
| |
Power @ 2,200 RPM |
242 kW |
325 hp |
| |
Runtime Hours: |
1,686 |
| |
Fuel capacity: |
1,135 liters |
300 gallons |
| |
Fuel consumption: |
60.2 liters/hr |
15.9 gallons/hr |
| Hydraulic Systems |
| |
Circuit #1: (Slurry Pump): |
6.4 in3/rev., 60 gpm (3.78 liter/sec.) @ 5,500 psig |
| |
Circuit #2: (Cutterhead, Boom, Winches and Starwheels) |
7.9 in3/rev. load sense, 75 gpm (4.73 liter/sec.) @ 2,500 psig |
| |
Reservoir: |
454 liters |
120 gallons |
| |
Filtration: |
(one) 1 tank mounted return filter with a 10 micron (min.) rating with a indicator & cab warning light. Slurry pump circuit remote charge filter 6-micron (min.) rating with an indicator & cab warning light. Filter with water removal capability are optional. |
| Cutterhead |
| |
Cutterbar: |
| |
Diameter: |
559 mm |
22 inches |
| |
Length: |
2.743 m |
108 inches |
| |
Replaceable hardened steel excavator blades; available with paddlebar for materials that are easily slurried. |
| |
Drive: |
Recessed dual hydraulic motor; direct drive with no gear reduction. |
| |
Speed (variable): |
0 to 95 RPM @ 2,500 psi |
| |
Torque: |
23,885 in-lbs (2,969 N-m) @ 2,500 psi (peak) |
| |
Cutter Tip Force: |
2,171 lbs (9,657 N) |
| Dredge Pump |
| |
Type: |
IMS |
| |
Discharge diameter: |
305 mm |
12 inches |
| |
Suction diameter: |
248 mm |
9.75 inches |
| |
Impeller diameter: |
489 mm |
19.25 inches |
| |
Sphere passage: |
152 mm |
6 inches |
| |
Pump performance: |
3,500 gpm (220 liter/sec.) @ 65 ft (19.8m) TDH (water) @ 990 RPM. Available rubber lined for use in abrasives. |
| |
Speed (variable): |
0 to 990 RPM |
| Controls |
| |
Electronic joystick controls are provided in a climate controlled cab. |
| Propulsion |
| |
Make/Model: |
Starwheel* Drive Self-Propulsion system; cable drive optional.
Starwheels* are individually operated for high maneuverability. |
| |
Speed (variable): |
0 to 15 RPM (starwheel drive) |
| |
|
0 to 55 fpm (cable drive) |
| Electric System |
| |
Voltage: |
12 volt, negative ground |
| |
Alternator Output: |
130 Amp |
| Corrosion Protection |
| |
Standard paint: |
Superstructure and hull are sandblasted and painted with two coats of marine epoxy suitable for saltwater service. A self healing zinc clad undercoating is applied to above deck surfaces. The cab is made with galvaneal steel. Submerged surfaces are top coated with two coats of anti-fouling paint. Average paint thickness is 12 mils minimum. |
| Cathodic Protection |
| |
Standard |
All details on these pages are given in good faith
and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose
is either stated or implied. Prices are subject to change without notice.
|
|
|
| DredgeBrokers © 2007 |
| Dredge Brokers Design by thewritersforhire.com |
Hydraulic Dredges