Dredge Brokers - Used Dredgers (Dredges) For Sale


10-inch (250 mm) Wolverine Dredge

10-inch (250 mm) Wolverine Dredge

The hull is composed of three compartments. The hull sides and deck is constructed from 10 gauge plate (3.57 mm). The bottom of the hull is constructed from 3/16” plate (4.7 mm). The ladder is constructed of 3”x3”x3/16” (76 mm x 76 mm x 4.7 mm) angle iron with 7 gauge (4.55 mm) metal plate gussets. The cutterhead has a 27” (686 mm) inside diameter back ring with an outside diameter of 32” (813 mm). The prime mover is a Caterpillar model C13 ACERT diesel engine rated 440 bhp (328 bkW). The dredge pump is a Metso Minerals, Thomas Simplicity series dredge pump model # J30. The nominal flow rate is 3,800 GPM (863 m3/hr) @ 200 feet H2O (61 m H2O). Two (2) spuds are located on the stern of the dredge. The spuds are SCH 40 8-5/8” (219 mm) diameter x 30’ (9.4 m) long.

Built around 2014 and had worked 3411 hours. Recently it has been completely serviced, updated and gone through. It has been painted with polyuria epoxies.

Price includes the following which is located in Mexico-

  • New pump
  • New spare cutting head, the head currently on the dredge is in great shape as well
  • Approximately 500 yards of pipeline
  • Many floats
  • The thermofusion (pipe welding) equipment is in great shape
Location: state of Texas, USA

Select Your Currency
Price in Seller's Preferred Currency
USD 300,000
Price in Your Preferred Currency
USD 300,000
* Approximate; see Terms of Use

Technical Details

General Information
  Built:  2014  
  Hours of Operation:  3411  
Principal Dimensions and Characteristics
  Length overall (with ladder): 20.7 m 68-ft
  Hull Length: 15.2 50-ft
  Hull Width: 3.5 m 11-ft 6-inch
  Hull Depth: 1.2 m 4-ft
  Over Height (trucking): 3.1 m 10-ft
  Total Dry Weight (approx.): 26,309 kg 58,000 lbs
  Diesel Fuel Capacity: 1,893 liters 500 gal
  Max Dredging Depth: 7.6 m 25-ft
  Make/Model: Caterpillar model C13 ACERT diesel
  Power: 328 bkW 440 bhp
Dredge Pump
  Make/Model: Metso Minerals, Thomas Simplicity series #J30
  Nominal Flow Rate: 863 m3/hr 3,800 gpm
  Cutter Head (inside diameter): 686 mm 27-inch
  Cutter Head (outside diameter): 813 mm 32-inch
  Cutter Design: six (6) smooth blades  
  Power at Shaft: five (5) cylinder Staffa hydraulic motor with model # HMB-200
Ladder and Swing Winches
  Ladder Length: 10 m 33-ft
  Winches Pull Capacity(5): 20kN 4,500 lb
  Wire Diameter: 10 mm 3/8-inch
  Wire Length: 45.7 m 150-ft
Spuds (2)
  Length: 9.4 m 30-ft
  Diameter: 219 mm 8-5/8-inch
  All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice
Copyright © 2021