191016-DB
16 x 12 Cutter Suction Dredger
This 16 x 12 Cutter Suction Dredger is a dismountable cutter suction dredger. The dredger has kicker spuds, allowing the dredger to be advanced without walking the dredger. Built in 2013 but not put into operation until 2014. The working hours is 6,800. The main pump was updated in 2020.
Located in Northern Europe
Select Your Currency:
Price in Seller's Preferred Currency:
USD
475,000
Price in Your Preferred Currency:
USD 475,000
* Approximate; see
Terms of Use
Technical Details
Principal Dimensions and Characteristics | |||
Length Hull: | 12.00 m | 39-ft | |
Length Overall: | 18.00 m | 59.05-ft | |
Beam: | 4.80 m | 16-ft | |
Depth: | 1.50 m | 5-ft | |
Mean Draft (w/full bunkers) approx.: | 0.88 m | 3-ft | |
Dredging Depth: | 11.00 m | 36-ft | |
Ladder Length: | 14.5 m | 47-6-ft | |
Total Dry Weight: | approx. 40 tons | ||
Main Engine | |||
Make/Model: | CAT C18 INDM |
||
Power @ 2,200 RPM: | 597 kW | 800 hp | |
Diesel Fuel Capacity: | 8000 ltr | 2113 gals | |
Dredge Pump | |||
Make/Model: | 16/12HG-II-(7)-850R-230-??? | ||
Impeller diameter: | 850 mm | 33.5-inch | |
Shaft Power @ 750 RPM: | 800 kW | 1,073 hp | |
Pump Capacity: | 3400 m3/hr | 4447 yd3/hr | |
Suction Pipe Diameter: | 400 mm | 16-inch | |
Discharge Pipe Diameter: | 304.8 mm | 12-inch | |
Gear Box | |||
Make/Model: | ZF 500 | ||
Type: | Vertical offset, direct mount marine transmission | ||
Cutter | |||
Cutter Diameter: | 1,200 mm | 47-inch | |
Material: | High manganese steel | ||
Number of Cutter Blades: | 5 | ||
Drivers: | Hydraulic Motor | ||
Cutter Power: | 30 kW | 40 hp | |
Service Pump | |||
Make/Model: | VARISCO (Italia) / N2SG 40-26.264 | ||
The service pump is provided to supply flushing water to the dredge pump packing gland, water to the cutter drive bearings and for a use at a deck connection. | |||
The hydraulic pump is a 2-section pump that provides service to the cutter head motor, swing winches, spud winches and ladder winch. The hydraulic system is protected by relief valves and the system has replaceable inline filters. The hydraulic system has an approximate capacity of 400 liters (106 gallons). | |||
Electrical System | |||
The electrical system consists of a 24-volt 65-amp alternator and a 240 amp/hr battery. The wring is a complete circuit with one (1) wire to ground through a full breaker panel. The lighting consists of seven (7) floodlights that are mounted on the dredge. Lighting is also provided in the engine/pump compartment, on the instrument panel and overhead in the lever room. | |||
Lever Room | |||
The lever room measures 1,800 mm x 1,900 mm x 1,900 mm (71 in. x 75 in. x 75 in.). All glass is LEXON 500 with 360 degree visibility. An upholstered seat is provided for the operator. The lever room is insulated for the reduction noise and for temperature control. The lever room is finished with a paneled interior. | |||
All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice. |