Dredge Brokers - Used Dredgers (Dredges) For Sale

150212-DH

10-inch Horizontal Dredger IMS 5012-LP

10-inch Horizontal Dredger IMS 5012-LP

This IMS Model 5012 LP Dredge came out of the water late last fall in 2014. It is ready for inspection and delivery.

Located in the state of Michigan, USA

The pipeline package is available for additional cost (file #150214-PP)

Select Your Currency
Price in Seller's Preferred Currency
USD 150,000
Price in Your Preferred Currency
USD 150,000
* Approximate; see Terms of Use

Technical Details

 
Principal Dimensions and Characteristics
  Length Over All: 12.9 m 42.5 feet
  Width: 3.4 m 11.3 feet
  Height:
  (with pre-cleaner removed): 3.1 m 10 feet
  Weight: (less fuel): 12,662 kg 27,915 lbs
  Displacement: 13,245 kg 29,200 lbs
  Draft: 762 mm 30 inches
Flotation
  Pontoons:
  Two (2) pontoons: 991 mm x 965 mm x 9,144 mm 39 in. x 38 in. x 360 in.
  10 ga. steel sides, bottom and 1/4" diamond plate tops; internal bulkheads and stiffeners,
  and coated w/marine grade epoxy-urethane paint.
Working Capacity         
  Cut (width x depth): 2.743 mm x 559 mm 108 in. x 22 in.
  Working Depth: 6.1 m 22 feet
  Extensions available to: 8.5 m 28 feet
Main Engine
  Make/Model: Cummins / 8.3 liter
  Power: 186 kW 250 hp
Hydraulic Systems
  Circuit #1: (Slurry Pump)
    6.4 in3/rev., 60 gpm (3.78 liter/sec.) @ 5,500 psig
  Circuit #2: (Cutterhead, Boom, Winches and Starwheels)
    7.9 in3/rev. load sense, 75 gpm (4.73 liter/sec.) @ 2,500 psig
  Reservoir: 454 liters 120 gallons
  Filtration: (one) 1 tank mounted return filter with a 10 micron (min.) rating
    with a indicator & cab warning light. Slurry pump circuit remote
    charge filter 6-micron (min.) rating with an indicator & cab
    warning light. Filter with water removal capability are optional.
Cutterhead           
  Cutterbar:
  Diameter: 559 mm 22 inches
  Length: 2.743 m 108 inches
  Replaceable hardened steel excavator blades; available with paddlebar for materials that are
  easily slurried.
  Drive: Recessed dual hydraulic motor; direct drive with no gear reduction.
  Speed (variable): 0 to 95 RPM @ 2,500 psi
  Torque: 23,885 in-lbs (2,969 N-m) @ 2,500 psi (peak)
  Cutter Tip Force: 2,171 lbs (9,657 N)
Dredge Pump  
  Type: IMS
  Discharge diameter: 305 mm 12 inches
  Suction diameter: 254 mm 10 inches
  Impeller diameter: 489 mm 19.25 inches
  Sphere passage: 152 mm 6 inches
  Pump performance: 3,500 gpm (220 liter/sec.) @ 65 ft (19.8m) TDH (water) @ 990 RPM.
    Available rubber lined for use in abrasives.
  Speed (variable): 0 to 990 RPM
Controls
  Electronic joystick controls are provided in a climate controlled cab.
Propulsion
  Cable Drive (No Starwheel)
Electric System
  Voltage: 12 volt, negative ground
  Alternator Output: 130 Amp
   
  All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice.
Copyright 2005