Dredge Brokers - Used Dredgers (Dredges) For Sale

160322-DH

10-inch Horizontal Cutter Dredger IMS 4010 - Refurbished

10-inch Horizontal Cutter Dredger IMS 4010 - Refurbished

This 10-inch Horizontal Cutter Dredger IMS 4010 was built in 1990 and has just been refurbished in 2016. It has been sand blasted and repainted with paint directly from IMS Dredge. Painted back to original paint specification. Ability to transport dredge depending on location in the U.S.A.

Located in the State of Illinois, USA

PRICE REDUCED FROM USD $150,000 FOR QUICK SALE

Select Your Currency
Price in Seller's Preferred Currency
USD 110,000
Price in Your Preferred Currency
USD 110,000
* Approximate; see Terms of Use

Technical Details

 
Principal Dimensions and Characteristics
  Year Built: 1990
  Length: 10.97 m 36.00 feet
  Width: 2.59 m 8.5 feet
  Height: 2.80 m 9.4 feet
  Dry Weight: 4,309 kg 9,500 lbs.
Main Engine
  Make / Model: Cummins / 6BTA (5.9 Liter Turbo Diesel)
  Power @ 2,500 rpm: 132 kW 177 hp
  Cylinders: 6
Flotation
  Pontoons x 4: 889 x 965.2 x 7,849 mm 35 x 38 x 309 inches
   

10 ga. steel sides and bottom w/ 1/4" diamond deck; internal

    bulkheads and stiffeners.
  Displacement: 10,160 kg 22,400 lbs.
  Draft (approx.) in Water: 381 mm 15 inches
Working Capacity
  Cut (width x Depth): 2,438.4 x 558.8 mm 96 x 22 inches
  Working Depth: 6.10 m 20 feet
Hydraulic Systems
  Hydraulic Pump: Sperry Vickers / 3525VQ38A1711BA20
  Capacity: @ 2,400 RPM Engine Speed Full Load
  Reservoir: 170 liters 45 gallons
    Equipped with low oil level and high oil temperature engine shut
    off or alarm contact switches.
  Relief Valve Setting: 2,100 PSI
  Hydraulic Oil Requirements: Cat Series 3 (15W40, 30WT, or 40WT)
  Fuel Requirements Reservoir: 341 liters 90 gallons
  Type of Fuel: No. 2 Diesel Fuel Only
Cutter Head
  Cutter bar:
  Diameter: 558.8 mm 22 inches
  Length: 2.43 m 8 feet
    Replaceable hardened steel excavator blades available with paddle
    bar for materials hat are not easily slurried.
  Drive: Recessed dual hydraulic motor; direct drive with no gear reduction.
  Speed: Variable to 90 RPM @ 2,500 PSI
  Torque: 12,960 in-lbs. (1,475 N-m) @ 2,500 PSI
Dredge Pump
  Type: IMS
  Discharge Diameter: 254 mm 10 inches
  Suction Diameter: 254 mm 10 inches
  Impeller Diameter: 495 mm 19.50 inches
  Sphere Passage: 152.4 mm 6.0 inches
  Pump Performance: 3,000 gpm @ (189 liter/sec) @ 70 ft. (21.30 m)
    TDH (water) @ 1,180 RPM
Others
  Controls: Electronic joystick controls are provided in a heated, air conditioned
  Propulsion: cable driven hydrolic motors
    individually operated for high maneuverability.
  Electrical System:
    Voltage: 12 volt, negative ground
    Alternator Output: 130 Amp
   
  All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice.
Copyright 2005