Dredge Brokers - Used Dredgers (Dredges) For Sale

160729-DH

IMS Model 5012 LP Versi-Dredge

IMS Model 5012 LP Versi-Dredge

This 10-inch Horizontal Cutter Dredger IMS 5012 was built in 2009 and is in very good condition and has 4,243.9 hours on it, At 4000-hours, the engine was replaced with a brand new unit. It last worked in 2011, maintenance and test run were last performed on July 21, 2016. The dredger is ready to work.

Located in Canada

Select Your Currency
Price in Seller's Preferred Currency
USD 125,000
Price in Your Preferred Currency
USD 125,000
* Approximate; see Terms of Use

Technical Details

 
Principal Dimensions and Characteristics
  Year Built: 2009
  Length Over All: 13 m 42.7 feet
  Width: 3.4 m 11.3 feet
  Height (w/pre-cleaner removed): 3.1 m 10 feet
  Weight (less fuel): 12,662 kg 27,915 lbs
  Displacement: 13,245 kg 29,200 lbs
  Draft: 762 mm 30 inches
Flotation
  Pontoons:
  Two (2) pontoons: 991 x 965 x 9,144 mm 39 x 38 x 360 inches
  10 ga. steel sides, bottom and 1/4" diamond plate tops; internal bulkheads and stiffeners, and
  coated w/marine grade epoxy-urethane paint.
Working Capacity         
  Cut (width x depth): 2,743 x 559 mm 108 x 22 inches
  Working Depth: 6.1 m 22 feet
  Extensions available to: 8.5 m 28 feet
Main Engine
  Make/Model: John Deere Diesel / 6090HF070 / 6 cyl. 9.0 liter
  Power @ 2,200 RPM 242 kW 325 hp
  Fuel capacity: 1,135 liters 300 gallons
  Fuel consumption: 60.2 liters/hr 15.9 gallons/hr
Hydraulic Systems
  Circuit #1 (Slurry Pump): 6.4 in3/rev., 60 gpm (3.78 liter/sec.) @ 5,500 psig
  Circuit #2 (Cutter head, Boom,
  Winches and Starwheels): 7.9 in3/rev. load sense, 75 gpm (4.73 liter/sec.) @ 2,500 psig
     
  Reservoir: 454 liters 120 gallons
  Filtration: (one) 1 tank mounted return filter with a 10 micron (min.) rating
    with a indicator & cab warning light. Slurry pump circuit remote
    charge filter 6-micron (min.) rating with an indicator & cab warning
    light. Filter with water removal capability are optional.
Cutter Head           
  Cutter Bar:
  Diameter: 559 mm 22 inches
  Length: 2.743 m 108 inches
  Replaceable hardened steel excavator blades; available with paddle bar for materials that are easily slurried.
  Drive: Recessed dual hydraulic motor; direct drive with no gear reduction.
  Speed (variable): 0 to 95 RPM @ 2,500 psi
  Torque: 23,885 in-lbs (2,969 N-m) @ 2,500 psi (peak)
  Cutter Tip Force: 2,171 lbs (9,657 N)
Dredge Pump  
  Type: IMS
  Discharge diameter: 305 mm 12 inches
  Suction diameter: 248 mm 9.75 inches
  Impeller diameter: 489 mm 19.25 inches
  Sphere passage: 152 mm 6 inches
  Pump performance: 3,500 gpm (220 liter/sec.) @ 65 ft (19.8 m) TDH (Water) @ 900
  Speed (variable): 0 to 990 RPM
Controls
  Electronic joystick controls are provided in a climate controlled cab.
Propulsion
  Make/Model: Starwheel* Drive Self-Propulsion system; cable drive optional.
    Starwheels* are individually operated for high maneuverability.
  Speed (variable): 0 to 15 RPM (starwheel drive)
    0 to 55 fpm (cable drive)
Electric System
  Voltage: 12 volt, negative ground
  Alternator Output: 130 Amp
Corrosion Protection            
  Standard paint: Superstructure and hull are sandblasted and painted with two coats
    of marine epoxy suitable for saltwater service. A self healing zinc
    clad undercoating is applied to above deck surfaces. The cab is
    made with galvaneal steel. Submerged surfaces are top coated with
    two coats of anti-fouling paint. Average paint thickness is 12 mils
    minimum.
Cathodic Protection            
  Standard
   
  All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice.
 
Copyright 2005