170105-DB
18-inch DSC "Shark" model 10300 Cutter Suction Dredge (CSD)
Manufactured by Dredging Supply Company, Inc, in 2012, this 18-inch Cutter Suction dredger had very little use when purchased by the current owners, and since then it has only worked on one job. Owners have been conscientious about maintenance, and have also reinforced some parts that they though could benefit from extra strength. The dredge comes with about 450 m or discharge pipeline, a backup cutter, and a Dredge Pack system for monitoring position and progress. The pipeline has abut 80% life left.
Location: Nicaragua
Select Your Currency:
Price in Seller's Preferred Currency:
USD
1,250,000
Price in Your Preferred Currency:
USD 1,250,000
* Approximate; see
Terms of Use
Technical Details
Principal Dimensions and Characteristics | ||||
Length Over All (with Ladder) | 112-feet, 4-inches | 34.00 m | ||
Length of Hull | 69-feet, 0-inches | 21.00 m | ||
Width: | 29-feet, 11-inches | 9.10 m | ||
Hull Depth | 5-feet, 0-inches | 1.50 m | ||
Draft With Fuel (Average) | 2-feet, 3-inches | 0.69 m | ||
Dry Weight (Approximate) | 215,000-pounds | 97.5-tonnes | ||
Year Built / Where Built | 2012 / USA | |||
Component Dimensions (approximate) | ||||
Side Sections (2x) | ||||
Length | 69-feet, 0 inches | 21.00 m | ||
Width | 10-feet 0-inches | 3.10 m | ||
Height | 5-feet, 0-inches | 1.50 m | ||
Center Section (without machinery room structure) | ||||
Length | 40-feet, 0-inches | 12.20 m | ||
Width | 9-feet, 11-inches | 3.00 m | ||
Height | 5-feet, 0-inches | 1.50 m | ||
Ladder (With Cutter Attached) | ||||
Length | 66-feet, 0-inches | 20.10 m | ||
Spuds (2x) | ||||
Type | Square | |||
Length | 69-feet, 4-inches | 21 m | ||
Width | 24-inches | 609 mm | ||
Weight | 12,647-pounds | 5,736 kg | ||
Dredging Capacities | ||||
Dredging Depth Minimum | 5-feet, 0-inches | 1.50 m | ||
Dredging Depth Maximum | 56-feet,0-inches | 17.00 m | ||
Pump | ||||
Make/Model: | Dredging Supply Company, Inc. / DSC 44-3V | |||
Suction Diameter: | 18-inches | 457 mm | ||
Discharge Diameter: | 18-inches | 457 mm | ||
Impeller Diameter | 44-inches | 1,118 mm | ||
Flow (Nominal) | 10,300 gpm | 650 L/sec | ||
Engine | ||||
Make / Model | Caterpillar / C-32 ACERT | |||
Rated Horsepower @ 2100 RPM | 1,125 hp | 839 kW | ||
Diesel Fuel Capacity | 2,550-gallons | 8,517 L | ||
Cutterhead Module | ||||
Cutting Force | 17,386-pounds | 77.3 kN | ||
Operating Torque | 434,655 in-lbs | 49,090 N-m | ||
Cutting Force per Linear Inch | 632 lb-in | 111 N-mm | ||
Cutter Diameter | 43-inches | 1,092 mm | ||
Shaft Diameter | 6.25-inches | 159 mm | ||
Power | 200 hp | 149 kW | ||
Speed (Variable) | 0-29 rpm | |||
Winches | ||||
Swing Winches (2x) | ||||
Make / Model | Dredging Supply Company, Inc. / WN200 | |||
Line Speed (1st Layer) | 76.50 ft/min | 0.38 m/sec | ||
Line Pull | 14,770-pounds | 66 kN | ||
Wire Size | 3/4-inches | 19.mm | ||
Drum Capacity | 576-feet | 176 m | ||
Ladder Winch | ||||
Make / Model | Dredging Supply Company, Inc. / WN200 | |||
Line Speed (1st Layer) | 76.50 ft/min | 0.38 m/sec | ||
Line Pull | 14,770-pounds | 66 kN | ||
Wire Size | 3/4-inches | 19.mm | ||
Drum Capacity | 576-feet | 176 m | ||
Spud Winches (2x) | ||||
Make / Model | Dredging Supply Company, Inc. / WN200 | |||
Line Pull (Bare Drum) | 22,266-pounds | 99 kN | ||
Wire Size | 5/8-inches | 16.mm | ||
All details on these pages are given in good faith and are believed to be accurate but no warranty of accuracy or completeness or suitability for purpose is either stated or implied. Prices are subject to change without notice |